Proszę nacisnąć odpowiedni nagłówek, aby rozwinąć artykuł.
-
Zastosowanie interfejsów idzie w kierunku zwiększenia ilości sposobów komunikacji użytkownika z komputerem. Weźmy pod uwagę rosnącą liczbę urządzeń podłączanych do komputerów, jak kamery czy aparaty cyfrowe bądź skanery. Duże firmy zaczynają się gubić w plątaninie kabli sieciowych. Rozwój komunikacji urządzeń peryferialnych z systemem wymaga użycia szybkich standardów komunikacyjnych czy też rewolucji na polu magistral systemowych. Wymiana bądź też serwisowanie peryferiali nie powinno przerywać pracy całego systemu i unieruchamiać rozpoczętych wcześniej procesów. Tak więc proponowany przez nas komputer PC powinien uwzględniać takie ewentualności.
USB (Universal Serial Bus) to standard wykorzystywany przez dzisiejsze urządzenia peryferyjne. USB v2.0 staje się wyznacznikiem komunikacji peryferiów z komputerem i dzięki swojej szybkości stanowi poważną konkurencję dla FireWire. Oznacza to, że możliwa stanie się obsługa wymagających urządzeń zewnętrznych, a tradycyjne będą potrzebowały o wiele mniej czasu na przesłanie danych. Jest już przesądzone, że nowe chipsety firmy Intel, począwszy od serii 845E z zaimplementowaną obsługą portów poprzez przyszłą generację 533QP Montara, do obsługi procesora Intel Banias, wypromują ten standard. (W Porównaniu z P4, Banias ma istotnie zmodyfikowaną architekturę i jest wyposażony w układy do komunikacji bezprzewodowej zgodnej ze specyfikacją IEEE802.11. Ponadto charakteryzuje się znakomitą technologią SpeedStep, regulującą pobór mocy w zależności od obciążenia obliczeniowego, co pozwoliło na 60% zmniejszenie wagi i użycie dwukrotnie mniejszego radiatora w stosunku do P4-M.) Powinny one obsługiwać 6 złącz USB. Urządzenia zgodne z tym standardem można podłączać w dowolnej chwili do komputera (tzw. hot plug).
FireWire (IEEE 1394) to nowoczesna magistrala szeregowa, jest jednym z najszybszych złączy jakie kiedykolwiek zostały opracowane dla urządzeń peryferyjnych. Przydaje się przede wszystkim do podłączania urządzeń multimedialnych, np. cyfrowych kamer, jak również urządzeń wymagających szybkiego przepływu danych, np. twardych dysków.
Umożliwia podłączenie i wymianę dysku także podczas pracy komputera. Ma również zastosowanie w aplikacjach video czy obsługi miniDV itp.
IrDA (Infrared Data Association) to standard transmisji danych bezprzewodowo w paśmie podczerwieni. Najczęściej używają go myszki, klawiatury i game-pady. Zastosowanie tego portu to także przesyłanie danych pomiędzy telefonami komórkowymi lub telefonem komórkowym i komputerem lub drukarką. Adapter pozwala korzystać z technologii IrDA po wpięciu do portu np. USB.
WLAN (Wireless Local Area Network) to sieć bezprzewodowa wykorzystująca fale radiowe, podczerwień lub też nawet laser. Zalety sieci bezprzewodowej są nieocenione. Komputery wchodzące w jej skład mogą być przemieszczane bez zrywania połączenia i rekonfiguracji sieci.
Standardy tej sieci definiują kilka poziomów bezpieczeństwa jej użytkowania. Działanie sieci bezprzewodowej opiera się na stałych punktach dostępowych i bezprzewodowych urządzeniach-klientach.
PATA (Parallel ATA) to rodzina kolejnych, rozwijanych interfejsów ATA/ATAPI do obsługi dysków. Bez wątpienia połączenie między kontrolerem a pamięcią masową musi dotrzymywać kroku zmianom, aby cały system działał wydajnie. Poszerzenie magistrali pomiędzy dyskiem twardym a kontrolerem, czyli zwiększenie jej przepustowości, jest niezbędne przy przesyłaniu danych. Większe bufory w twardych dyskach stają się zbędne, gdyż dane nie będą w nich długo przetrzymywane, lecz z dysku natychmiast przekazywane dalej.
SATA (Serial ATA) to następca PATA i ma zastąpić interfejs równoległy. Będzie miał duże znaczenie związane z mniej kłopotliwym podłączaniem urządzeń do komputera. Kontrolery SATA zapewnią szybki dostęp do nośników danych, zwłaszcza dysków twardych oraz CD/DVD.
SCSI (Small Computer System Interface) to interfejs dyskowy kojarzony zwykle z zastosowaniami profesjonalnymi. Służy do podłączania i komunikowania się z komputerem urządzeń nie korzystających z magistrali systemowej. Ideą działania SCSI jest korzystanie z niezależnej szyny komunikacyjnej, przypominającej małą sieć komputerową, z wydzieloną jednostką realizującą samodzielnie operacje I/O, będącą kontrolerem głównym oraz pewną grupą kontaktujących się z nią urządzeń. W niektórych wersjach wprowadzono zaawansowane mechanizmy pracy wielowątkowej.
PCI-X zwiększa dwukrotnie szybkość dotychczasowej PCI, przenosi dane równolegle po 64 ścieżkach. Umożliwia użytkownikowi systemu wymianę lub włożenie nowego urządzenia PCI bądź PCI-X bez potrzeby wyłączania systemu (hot plug). Możliwe jest także instalowanie dodatkowych złącz PCI/PCI-X będących fizycznie na zewnątrz komputera czy serwera. Warto pamiętać, pomimo iż PCI-X jest następca szyny PCI, to zostanie zastąpiony w przyszłości złączem PCI Express.
PCI Express (3GIO) - magistrala I/O nowej generacji. Zgodne z nią urządzenia będą korzystały z szeregowego przesyłania danych. Ponadto standard ten umożliwi używanie różnych rodzajów połączeń (elektrycznych lub optycznych), zapewni zgodność oprogramowania ze starszymi wersjami PCI, a niektóre jego dodatki być może pozwolą na przyłączenie także przyszłych wersji magistrali PCMCIA.
Technologię PCI Express zaprojektowano do współpracy z przyszłymi procesorami i pamięciami, pozwalając na wydajną komunikację z CPU o dużej częstotliwości zegara. Pomimo, że PCI Express jest przyszłościowym rozwiązaniem, nie rozstaje się definitywnie z obecną specyfikacją PCI.
-
Light Peak – nazwa kodowa nowej technologii szybkich kabli światłowodowych firmy Intel zaprojektowanej do łączenia różnych urządzeń elektronicznych ze sobą. Złącze pozwoli na wykorzystanie pasma 10 Gb/s, z możliwością późniejszego zwiększenia do 100 Gb/s w ciągu następnych lat. Chociaż aktualnie w sprzedaży nie ma nośników, które obsłużyłyby taką prędkość, teoretycznie przy 10 Gb/s pełnometrażowy film zapisany w standardzie Blu-Ray będzie można przenieść w 30 sekund. Standard z założenia ma być następcą aktualnych magistrali, takich jak USB, FireWire czy HDMI. Teoretycznie jeden kabel światłowodowy w standardzie Light Peak mógłby zastąpić 50 kabli miedzianych, na przykład podczas kręcenia filmu. Demonstracja technologii Light Peak odbyła się 23 września 2009 podczas Intel Developer Forum. Intel ma nadzieję rozpocząć dystrybucję Light Peak w 2010. Według portalu Engadget technologia została wyprodukowana przez firmę Intel we współpracy z Apple Inc.
Light Peak cechuje się poniższą specyfikacją:
- prędkość 10 Gb/s przez kabel światłowodowy (do 100 metrów długości),
- równoczesne połączenie z wieloma urządzeniami,
- wiele protokołów,
- równoczesny transfer w obydwie strony,
- implementacja quality of service,
- hot plugging
Dodatkowo Intel pracuje nad dołączeniem do kabla części miedzianej, aby można było wykorzystać Light Peak również do zasilania urządzeń.
-
Description v1.1
- Speed: 1,5 & 12MBit/s
- Length: 3m
- Num. Repeater: 5
- Max. Current: 0.5Amp/5V
- Max. Devices: 127 HotPlug
- Peripherials:
- KBD
- Mouse
- LAN
- WLAN
- Scanner
- Printer
- CAM's
- Flash Reader
- Support:
- Win-2K
- Win-ME
- Win-XP
- Linux
- Bootsupport:
- Chipsets:
Description v2.0
- Speed: 1,5 & 12MBit/s & 480MBit/s
- Length: 3m
- Num. Repeater: 5
- Max. Current: 0.5Amp/5V
- Max. Devices: 127 HotPlug
- Peripherials:
- Support:
- Bootsupport:
- Chipsets:
Description v3.0
A new major feature is the "SuperSpeed" bus, which provides a fourth transfer mode at 5.0 Gbit/s. The raw throughput is 4 Gbit/s, and the specification considers it reasonable to achieve 3.2 Gbit/s (0.4 GByte/s or 400 MByte/s), or more, after protocol overhead.
When operating in SuperSpeed mode, full-duplex signaling occurs over two differential pairs separate from the non-SuperSpeed differential pair. This results in USB 3.0 cables containing two wires for power and ground, two wires for non-SuperSpeed data, and four wires for SuperSpeed data, and a shield that was not required in previous specifications.
To accommodate the additional pins for SuperSpeed mode, the physical form factors for USB 3.0 plugs and receptacles have been modified from those used in previous versions. Standard-A cables have extended heads where the SuperSpeed connectors extend beyond and slightly above the legacy connectors. Similarly, the Standard-A receptacle is deeper to accept these new connectors. On the other end, the SuperSpeed Standard-B connectors are placed on top of the existing form factor. A legacy standard A-to-B cable will work as designed and will never contact any of the SuperSpeed connectors, ensuring backward compatibility. SuperSpeed standard A plugs will fit legacy A receptacles, but SuperSpeed standard B plugs will not fit into legacy standard B receptacles, so a new cable can be used to connect a new device to an old host, but not to connect a new host to an old device; for that, a legacy standard A-to-B cable will be required.
SuperSpeed establishes a communications pipe between the host and each device, in a host-directed protocol. In contrast, USB 2.0 broadcasts packet traffic to all devices.
USB 3.0 extends the bulk transfer type in SuperSpeed with Streams. This extension allows a host and device to create and transfer multiple streams of data through a single bulk pipe.
New power management features include support of idle, sleep and suspend states, as well as link-, device-, and function-level power management.
The bus power spec has been increased so that a unit load is 150 mA (+50% over minimum using USB 2.0). An unconfigured device can still draw only one unit load, but a configured device can draw up to six unit loads (900 mA, an 80% increase over USB 2.0 at a registered maximum of 500 mA). Minimum device operating voltage is dropped from 4.4 V to 4 V.
USB 3.0 does not define cable assembly lengths, except that it can be of any length as long as it meets all the requirements defined in the specification. Although electronicdesign.com estimated cables will be limited to 3 m at SuperSpeed, cables which support SuperSpeed are already available up to 5 m in length.
The technology is similar to a single channel ("1×") of PCI Express 2.0 (5 Gbit/s). It uses 8B/10B encoding, linear feedback shift register (LFSR) scrambling for data and spread spectrum. It forces receivers to use low frequency periodic signaling (LFPS), dynamic equalization, and training sequences to ensure fast signal locking.
www.usb.org
-
Description
- Speed: 480MBit/s
- Length: 4,5m
- Num. Repeater: 16
- Max. Current: 1.5Amp/12V
- Max. Devices: 63, HotPlug
- Peripherials:
- Harddisk
- CD, DVD, -RW
- CAM's
- LAN
- WLAN
- Support:
- Win-2K
- Win-ME
- Win-XP
- LINUX
- Boot support:
- Chipsets:
IEEE1394b Firewire
Under definition!
Higher speeds: 800, 1600, 3200 Mbit/sec
www.intel.com
www.ti.com
-
Parallel-ATA
Description
Designs |
Speed |
Max. Length |
ELANxxx |
33Mbit/s |
0.45m |
TX, BX |
33Mbit/s |
0.45m |
815E |
66MBits/s |
0.33m |
815E, 845G |
100MBit/s |
0.25m |
Speed |
Max. Length |
ATAPI-2 |
16MByte/s |
0.45m |
IDE |
ATAPI-3 |
16MByte/s |
0.45m |
EIDE |
ATAPI-4 |
33MByte/s |
0.33m |
ULTRA |
ATAPI-5 |
66MByte/s |
0.33m |
28LBA |
ATAPI-6 |
100MByte/s |
0.25m |
48LBA |
ATAPI-7 |
133MByte/s |
0.25m |
48LBA |
www.t13.org
www.ata-atapi.com
-
Serial-ATA
Serial-ATA G1
Designs |
Speed |
Freq. |
Max.Length |
P4-ICH5 |
150MByte/s |
1.2GHz |
1m |
Serial-ATA G2/3
Designs |
Speed |
Freq. |
Max.Length |
P4-ICH6
|
300MByte/s |
2.4GHz |
1m |
600MByte/s |
4.8GHz |
1m |
www.serialata.org
-
SCSI
Description
- Speed: 10-640MByt/s
- Length: 6m
- Num. Repeater: 8/16-lines
- Max. Current: 1Amp
- Max. Devices: 8
IEEE1394b Firewire
Under definition!
- Higher speeds: 800, 1600, 3200 Mbit/sec
www.t10.org
-
FeaturePak is a new and innovative approach to mezzanine-style expansion of computer-on-module (COM) baseboards, single-board computers (SBCs), and proprietary embedded electronics. Additionally, the FeaturePak approach is highly synergistic with existing and emerging bus-, I/O-, chip- and board-level technologies, and satisfies the need for a low-profile, cost-effective way to add off-the-shelf I/O expansion options to embedded designs. In short, we believe it represents the “Next Big Thing” in modular embedded computing.
The FeaturePak standard was originated by Diamond Systems Corp., one of the first supporters of the venerable PC/104 modules standard. Although PC/104 and PC/104-like stackable modules have evolved to encompass new technologies, there was a perceived need for an even smaller, lower-profile, mezzanine-style expansion format for use on tomorrow’s compact, highly-integrated SBCs and COM baseboards. The FeaturePak standard was developed to fill this gap in what was currently available in the embedded market.
Key FeaturePak features:
- Compact, low profile form-factor — 3/5 the size of a credit card and 1/3 the size of a PC/104 module
- Single low-cost connector integrates all host and external I/O interfaces
- Provides up to 100 I/O points per module
- Leverages industry-standard buses such as PCIe, USB, and I2C
- Host processor and factor agnostic
- Coexists with PC/104, SUMIT, Qseven, ETX, XTX, COM Express, etc.
- Multiple FeaturePaks may be present within one system
- Zero height expansion module
- Open industry standard
- Rugged and reliable
Key FeaturePak benefits:
- Shortens time-to-market
- Reduces board-level development costs and risks
- Simplifies system design
- Eliminates cables, resulting in higher reliability, lower cost, and faster assembly
- Enables scalable and reconfigurable system design
- Enables easy product upgrades
- Protects from component obsolescence
- Encapsulates intellectual property
- Suitable for SBCs, baseboards, and proprietary all-in-one hardware designs
- Ideal for rapid-prototyping through high-volume applications
- Ideal format for silicon vendor reference designs
- Open standard increases market acceptance
-
LAN
Description
LAN |
Speed |
Controller |
10/100MB
|
10 & 100MBit/s
|
82C559 |
82C551 |
10/100/1000MB |
10-1000MBit/s |
82C554 |
-
WLAN IEEE802.11
Description
Standard |
802.11 |
802.11a |
802.11b |
Bandwidth |
83MHz |
300MHz |
83.5MHz |
Frequencies |
2.4GHz |
5GHz |
2.4GHz |
Datarate |
2Mb/s |
54Mb/s |
11Mb/s |
Approved |
1997 |
1999 |
1999 |
Compatibile |
- |
WiFi5 |
WiFi |
Application |
old |
speed |
SOHO |
www.wlana.org
-
PCMCIA
Description
PCMCIA (Personal Computer Memory Card International Association) is an international standards body and trade association with over 200 member companies that was founded in 1989 to establish standards for Integrated Circuit cards and to promote interchangeability among mobile computers where ruggedness, low power, and small size were critical. As the needs of mobile computer users has changed, so has the PC Card Standard. By 1991, PCMCIA had defined an I/O interface for the same 68 pin connector initially used for memory cards. At the same time, the Socket Services Specification was added and was soon followed by the Card Services Specifcation as developers realized that common software would be needed to enhance compatibility.
In more recent years, PCMCIA has realized the need for higher speed applications such as multimedia and high-speed networking. From this realization came the CardBus and Zoomed Video Specifications which allow blazing speed in such applications as MPEG video and 100 Mbit Ethernet. Along with these speed enhancements, PCMCIA has continued to add to its specification to enhance compatibility and allow for such other mobile-oriented concerns as 3.3V operation and Power Management.
Today, PCMCIA promotes the interoperability of PC Cards not only in mobile computers, but in such diverse products as digital cameras, cable TV, set-top boxes, and automobiles. As the variety of products that need modular peripheral expansion has grown, so has the diversity of the capabilities of modular peripherals. As such, PCMCIA has recently changed its mission statement: "To develop standards for modular peripherals and promote their worldwide adoption."
PCMCIA's new mission is exemplified by its work with standards for small form factor cards. PCMCIA has added the Small PC Card form factor specifications to the PC Card Standard and now publishes and maintains the Miniature Card Standard. Also, PCMCIA will be publishing the SmartMedia Card Standard which already provides memory solutions in one of the smallest modular peripheral form factors today.
All of these cards enable hand-held devices such as digital cameras to use a very small, rugged form of memory while PC Cards will allow the data to be easily transferred to your personal computer through inexpensive adapters. As computing needs become faster and smaller, PCMCIA continues to set the standard.
www.pcmcia.org
-
CardBUS
Description
CardBus is based upon the same physical specifications as PCMCIA and uses the same connectors. It's different from other PC cards in that CardBus has a 32-bit multiplexed address/data path, which operates at PCI local-bus speeds of up tp 33MHz, producing a peak bandwidth of 132MB/s. CardBus accomplishes this by adopting the synchronous burst transfer orientation of PCI, as well as a bus protocol, which is essentialy identical to that of PCI.
CardBus is a hotplug interface for many peripheral function cards.
Bit: 32
Speed: 33MHz
Rate: 1GB/s
Len: 0.1m
Nodes: 2
Medium: Cu
www.pcmcia.com
-
S/PDIF
Description
(Sony/Philips Digital Interface) is a newest audio transfer file format, which provides impressive quality through optical fiber and allows you to enjoy digital audio instead of analog audio. Normally thera are two S/PDIF outputs, one for RCA connector, the most common one used for consumer audio products, and the other for optical connector with a even better audio quality. Through a specific audio cable, you can connect the SPDIF connector to the other end of S/PDIF audio module, which bears S/PDIF digital output. However, you must have a S/PDIF supported speaker with SPDIF digital input to connect the SPDIF digital output to make the most out of this function.
Wires/Link: 1
Speed: 5MHz
Rate: 5Mb/s
Len: 5m
Nodes: 1
Medium: Cu/FO
www.sony.com
|